New Technology Solves Aftermarket Parts Problems

Written by: Dr. T. Ravisundar and Dibu Chowdhury, HydroAire, Inc,. and Heinz P. Bloch, P.E., Process Machinery Consulting
Publisher: Pumps & Systems / March, 2014


Industrial equipment users are often confronted with pump parts issues and must make choices. Handling these issues requires making experience-based decisions and prioritizing. How pump hydraulic and wear components in existing inventory are treated is an issue that merits consideration. Plant size, age, past purchasing, maintenance and storage-related practices are among the factors that affect a facility’s status with respect to operational readiness and downtime risk.

As these generally-known facts are applied on a pump component level, it is often determined that the specific pump components in the storehouse may not be the same as the components currently operating in a particular process centrifugal pump. Nor is it always the case that truly optimized components are presently installed. Therefore, the risk of experiencing unforeseen downtime can be reduced by having the right parts on hand. If the parts are truly optimized, installing them at the next opportunity will take the facility beyond being back in business—it will actually take the equipment owners to greater profitability.

To ensure that pumps will perform their intended functions, inventoried or stocked parts should be thoroughly inspected and corrected as needed prior to installation. Incoming inspection is practiced by best-of-class equipment owners and only verified-as-correct parts will be placed in the storehouse. This case study examines a real-life scenario and demonstrates essential precautions that can be taken when procuring pump hydraulic and wear components.


A Condensate Pump Repaired & Improved

During a planned outage, a nuclear power plant (NPP) sent a three-stage condensate pump to a highly experienced service center with hydraulic pump design engineers on staff. The NPP provided the hydraulic components, wear rings and bearings from its stock inventory for the pump rebuild project. The hydraulic pump design engineers at the service center performed a thorough inspection of both the disassembled rotor and the parts supplied by the NPP. A visual inspection quickly revealed that the geometry of the replacement impellers did not match the impellers that were removed from the disassembled pump (see Figure 1).


Figure 1. Cross-section of a three-stage pump created by an experienced pump repair facility for this three-stage pump. Note semi-open impellers in stages two and three.



Left: Impeller from disassembled pump
A) Leading edge of vane is straight.
B) Ring turn face to leading edge dist ~ 7/16 inch

Right: Spare impeller supplied from inventory
A) Leading edge of vane edge is curved.
B) Ring turn face to leading edge dist ~ 1inch


Figure 2. Vane condition, first-stage impeller



Left: First stage impeller from disassembled pump Properly trimmed vane

Right: Spare impeller supplied from inventory
Protruded vanes, possibly caused by core shift during casting process

Figure 3. Vane condition, first-stage impeller



Left: Impeller from disassembled pump
Suction eye diameter is machined Inlet throat area (arrow) ~30.6 sq. inch

Right: Spare impeller supplied from inventory
Suction eye diameter is as-cast Inlet throat area (arrow) ~27.6 sq. inch


Figure 4. First stage impeller from three-stage pump (left) and from owner’s inventory (right)



First Mapping, then Comprehensive Engineering Analysis

Figures 1 through 6 are examples of the extensive mapping of before versus after conditions of virtually all components of this condensate pump. The service center hydraulic pump design engineers performed comprehensive engineering analyses which overlapped and intermeshed the mappings. In this instance, the analyses included three-dimensional (3-D) modeling using late edition ANSYS software.


Figure 5. Overlapping of 3-D models for engineering review

Figure 6. Performance predictions were part of an analytical study performed by the service center’s in-house hydraulic pump design engineers



Restoring the Impellers

The service center engineers’ comprehensive engineering analysis determined that using the replacement impellers would alter the pump’s hydraulic performance. Therefore, the service center proposed suitable modifications to each of the three stages. On the spare suction impeller, the modifications included profiling the vane inlet to increase the throat area, enlarging the suction eye diameter and tapering the vane outlet to correct the protrusions shown in Figures 2 and 3. The proposed modifications for the intermediate stage impellers included the proper profiling of the vane outlet in addition to trimming and “underfiling” the diameters to the appropriate dimensions. With the NPP’s approval, the service center made the modifications and polished the flow passages to improve the hydraulic performance of each spare impeller.


Figure 7. One of two semi-open spare impellers after modification



Wear Rings & Bearings

The service center’s in-house engineering team evaluated the wear rings and bearings supplied by the NPP’s store room. Next, the NPP was informed of the nature of the component discrepancies and that the dimensions of as-supplied spare parts would not meet sound acceptance criteria.
Both pump owner’s and the service center’s engineers reviewed the reasons the service center advocated proper wear ring dimensions and how deviations would prevent this pump from performing as intended. The NPP concurred and asked the service center to manufacture new wear rings with proper running clearances.
Pump users have ample data on the effects of excessive running clearances on performance. While clearances can become enlarged as a result of galling and sometimes corrosion in service, they should be correct and within reasonable limits when first installed. The same reasoning is true for the bearings shown in Figure 1. When the service center engineers reviewed the original equipment manufacturer (OEM) design manual to ensure that the carbon bearing was supplied from the owner’s store room, it was discovered that at least one of the spare bearings would not satisfy the design requirements. The service center was asked to obtain a new carbon bearing with the proper clearances.


Testing to Prove Pump Performance

The NPP agreed to have the rebuilt pump tested at the service center’s independent test lab in Chicago. The results of the test are shown in Figure 8. The plots confirmed that pump performance was enhanced and that no increase in power demand would occur. The engineered upgrades improved the pump’s efficiency, which translates into a reduced carbon foot print and energy savings for the NPP’s owners.


Figure 8. Before versus after performance plots



Summarizing the Guidelines

Important guidelines for the procurement of important spare parts can be inferred from the case history presented here:


  • Purchase wear components with extra stock. Finish-machined parts may not fit in repaired bowls and impellers. When purchasing spare parts, make sure there is extra stock to allow the components to be machined to size. This will provide an optimal fit, which will help reduce the likelihood of problems upon startup and during operation.
  • Test hydraulic components prior to re-installing an essential pump. Pump rotor refurbishment will usually present an opportunity to obtain accurate performance data. A test plot will ensure the spare or rebuilt rotor will perform its intended function. Ensuring repeatability of pump performance is especially critical for safety-related pumps.
  • Use checks and balances in the inventory-receiving process. Whether replacement parts are ordered from the OEM or a third-party supplier, always have a method of checking the parts to ascertain equivalency of the hydraulic components. It is important to document the various and sundry “attributes of parts and components.” This may be accomplished by cataloging component particulars for the owner entity’s in-house records. If inconsistencies are found, contact the supplier. Ask the supplier to explain and/or rectify discrepancies. When in doubt, work with an experienced and reliable pump service center. Such a service center will have its own engineering group.

This article highlights opportunities to combine pump repair and pump upgrading. Although the advantages of planning for such profitability enhancement are intuitively evident, occasional reminders are needed. New technology offers options which allow for solid model studies to be performed for parts comparisons. Take the opportunity to work with an experience service provider to have your parts reverse engineered during routine maintenance events. Taking this approach will enable pump owners to save significant amounts of money, time and difficulties.

Posted in Case Studies and tagged , , .